Elica ETOILE User Manual download pdf (Page 11)

Additional Installation Specifications:

Use only the fixing screws supplied with the product for installation

or, if not supplied, purchase the correct screws type.

Use the correct length for the screws which are identified in the

Installation Guide.

In case of doubt, consult an authorised service assistance centre

or similar qualified person.

WARNING! Failure to install the screws or fixing device in

accordance with these instructions may result in electrical hazards.

Use

The hood is designed to be used either for exhausting or filter

version.

Ducting version

In this case the fumes are conveyed outside of the building by

means of a special pipe connected with the connection ring

located on top of the hood.

Attention! The exhausting pipe is not supplied and must be

purchased apart.

Diameter of the exhausting pipe must be equal to that of the

connection ring.

In the horizontal runs the exhausting pipe must be slightly slanted

(about 10°) and directed upwards to vent the air easily from the

room to the outside.

Attention! If the hood is supplied with active charcoal filter, then it

must be removed.

Connect the hood and discharge holes on the walls with a

diameter equivalent to the air outlet (connection flange).

Using the tubes and discharge holes on walls with smaller

dimensions will cause a diminution of the suction performance and

a drastic increase in noise.

Any responsibility in the matter is therefore declined.

! Use a duct of the minimum indispensible length.

! Use a duct with as few elbows as possible (maximum elbow

angle: 90°).

! Avoid drastic changes in the duct cross-section.

! Use a duct as smooth as possible inside.

! The duct must be made of certified material.

Filter version

One active charcoal filter is needed for this and can be obtained

from your usual retailer.

The filter removes the grease and smells

from the extracted air before sending it back into the room through

the upper outlet grid.

Installation

The minimum distance between the supporting surface for the

cooking equipment on the hob and the lowest part of the range

hood must be not less than 65cm from electric cookers and 65cm

from gas or mixed cookers.

If the instructions for installation for the gas hob specify a greater

distance, this must be adhered to.

NOTE= For proper operation it is recommended to install the

product at a distance of 200 - 210 cm from the floor

Electrical connection

The mains power supply must correspond to the rating indicated

on the plate situated inside the hood. If provided with a plug

connect the hood to a socket in compliance with current

regulations and positioned in an accessible area, after installation.

If it not fitted with a plug (direct mains connection) or if the plug is

not located in an accessible area, after installation, apply a double

pole switch in accordance with standards which assures the

complete disconnection of the mains under conditions relating to

over-current category III, in accordance with installation

instructions.

Warning! Before re-connecting the hood circuit to the mains

supply and checking the efficient function, always check that the

mains cable is correctly assembled.

Warning! Power cable replacement must be undertaken by the

authorised service assistance centre or similar qualified person.

Mounting

This type of cooker hood must be fixed to the ceiling.

Very heavy product; hood handling and installation must be

carried out by at least two persons.

Before beginning installation:

• Check that the product purchased is of a suitable size for the

chosen installation area.

• Check (for transport reasons) that there is no other supplied

material inside the hood (e.g. packets with screws (*),

guarantees (*), etc.), eventually removing them and keeping

them.

• If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to rear

wall/ceiling. Otherwise put a thick, protective covering over

countertop, cooktop or range to protect from damage and

debris. Select a flat surface for assembling the unit. Cover

that surface with a protective covering and place all canopy

hood parts and hardware in it.

• In addition check whether near the installation area of the

hood (in the area accessible also with the hood mounted) an

electric socket is available.

• Carry out all the masonry work necessary (e.g. installation of

an electric socket).

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must verify

suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take the

weight of the hood. Do not tile, grout or silicone this appliance

to the wall. Surface mounting only.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 59 60

Comments to this Manuals

No comments

Elica ETOILE User Manual Page 11

Comments to this Manuals

Related products and manuals for Hoods Elica ETOILE