ELICA Leaf User's Guide download pdf (Page 12)

Grease filter signal

After 40 hours of operation LED 1 flashes.

When such signal appears the grease filter installed needs to

be washed.

To reset the signal, keep T4 button pressed for 5”.

The hood gives out a "BEEP" and LED 1 stops flashing.

Charcoal filter signal

After 160 hours of operation LED 2 flashes.

When such signal appears the charcoal filter installed must be

replaced.

To reset the signal, keep T4 button pressed for 5”.

The hood gives out a "BEEP" and LED 2 stops flashing.

In case of contemporaneous signalling of both filters, LEDs 1

and 2 flash alternatively.

To reset, carry out the procedure described above for 2 times.

The first time it resets the charcoal filter signal, the second

time it resets the grease filter signal.

The charcoal filter signal is not active in the standard mode.

In case the hood is used in filter version it is necessary to

enable the charcoal filter signal.

Activating charcoal filter signal:

Set the hood to OFF and press T4 button for 5”.

Once the button has been pressed, the LEDs related to the

filter signals currently active light up.

The hood gives out a "BEEP" and LED 2 flashes for 2".

LEDs 1 and 2 remain on for about 2" before the hood goes

back to OFF.

Deactivating charcoal filter signal:

Set the hood to OFF and press T4 button for 5”.

Once the button has been pressed, the LEDs related to the

filter signals currently active light up.

The hood gives out a "BEEP" and LED 2 switches off.

LED 1 remain on for about 2" before the hood goes back to

OFF.

Maintenance

ATTENTION! Before performing any maintenance operation,

isolate the hood from the electrical supply by switching off at

the connector and removing the connector fuse.

Or if the appliance has been connected through a plug and

socket, then the plug must be removed from the socket.

Cleaning

The cooker hood should be cleaned regularly (at least with the

same frequency with which you carry out maintenance of the

fat filters) internally and externally. Clean using the cloth

dampened with neutral liquid detergent. Do not use abrasive

products. DO NOT USE ALCOHOL!

WARNING: Failure to carry out the basic cleaning

recommendations of the cooker hood and replacement of the

filters may cause fire risks.

Therefore, we recommend oserving these instructions.

The manufacturer declines all responsibility for any damage to

the motor or any fire damage linked to inappropriate

maintenance or failure to observe the above safety

recommendations.

Steam screen

The steam screen must always be left closed and opened only

for maintenance (e.g. cleaning or changing filters).

Grease filter

Fig. 12-25

Traps cooking grease particles.

This must be cleaned once a month (or when the filter

saturation indication system – if envisaged on the model in

possession – indicates this necessity) using non aggressive

detergents, either by hand or in the dishwasher, which must

be set to a low temperature and a short cycle.

When washed in a dishwasher, the grease filter may discolour

slightly, but this does not affect its filtering capacity.

Open the steam screen.

To remove the grease filter, pull the spring release handle.

Charcoal filter (filter version only)

Fig. 24

It absorbs unpleasant odours caused by cooking.

The charcoal filter can be washed once every two months

using hot water and a suitable detergent, or in a dishwasher at

65°C (if the dishwasher is used, select the full cycle function

and leave dishes out).

Eliminate excess water without damaging the filter, then put it

in the oven for 10 minutes at 100° C to dry completely.

Replace the mattress every 3 years and when the cloth is

damaged.

• Montage

Open the steam screen and remove the grease filter.

Install the carbon filter on the back of the grease filter and

fix with two rods.

Attention! The rods are included in the carbon filter

packing and not on the hood.

• To dismantle the filter act in the reverse manner.

Replacing lamps

Fig. 26

Disconnect the hood from the electricity.

Warning! Prior to touching the light bulbs ensure they are

cooled down.

• Remove the top cover for access to the neon bulb

compartment.

• Remove the bulb and replace with a new one, use only

neon bulbs type G5-T5 14W max (4000°K).

If the lights do not work, make sure that the lamps are fitted

properly into their housings before you call for technical

assistance.

1 2 ... 7 8 9 10 11 12

Comments to this Manuals

No comments

ELICA Leaf User's Guide Page 12

Comments to this Manuals

Related products and manuals for Cooker hoods ELICA Leaf